Installation

Miami Laminate Flooring Installation Materials

Our team of professionals knows what it takes to get the job done when it comes to installing Miami Laminate Flooring offers. Below you will find the materials most commonly used throughout the process.

Materials:

• Straight edge
• Measuring tape
• Pencil
• Marker
• Speed square
• Scissors
• Hammer
• Coping saw
• Circular saw with fine-tooth blade
• Safety goggles
• Clamps
• Laminate wood flooring

You can install laminate wood floors on top of an existing floor as long as the floor is flat and solid. The foam pad will make up for irregularities and help keep the floor quiet. You must first check any door clearances before you install laminate flooring on top of an existing floor.

If you plan to cover an entire floor, keep the edges 1/4″ away from walls to allow for expansion and contraction. You can hide the exposed edges with trim or molding. Next, we will take a look at the installation process.

Installing The Best Wood Flooring Miami Offers

Once the right materials are on site, the installation process can begin. When it comes to wood flooring, Miami can bring about some challenges for homeowners. Things like humidity and temperature must be taken into consideration. Leave it to a team of professionals to get the job done. Below you will find the steps taken to install both the underlayment and flooring in a home or building.

Install Underlayment:

1. Measure the area of the floor you plan to cover and add 10 percent to allow for waste.

2. Remove the shoe molding from around the baseboard. Remove any doors from the area to be covered.

3. The flooring planks will need additional clearance to fit under door frames. Place a piece of underlayment and laminate flooring next to the jamb to determine the appropriate height and cut out the desired area of the frame with a handsaw.

4. Install the floor underlayment. Make sure the edges don’t overlap and tape the pieces together to prevent them from shifting. Create an expansion gap between the underlayment and the walls by using spacers.
* In addition to reducing noise, the underlayment cushions the laminate flooring to make it more comfortable to walk on. Underlayment comes in large rolls or as separate pieces that can be taped together.
* If you’re placing a laminate floor on top of a concrete slab, apply a polyethylene plastic vapor barrier before installing the underlayment.

Install the flooring

Before you install the laminate wood floors, store them inside your house to acclimate it to room temperature. This will help prevent the flooring from accumulating moisture and will reduce expansion and contraction during installation. Check for damage on each plank before installation. Individual planks can be very difficult to remove after they’re set in place. Your beginning wall (the wall where you first started installing the new floor) should be more visible than your ending wall. Plan your installation so that any irregularities in the ending wall will be hidden by appliances or furniture. Plan your installation so that the flooring helps emphasize the focal point of the room.
The planks along the edges should be at least 2″ wide. Check your measurements before you begin to make sure the planks along your ending wall won’t be too narrow.

1. Dry fit the first three rows of planks. If your beginning wall is uneven or has contours, you’ll need to trace a pattern in order to cut the laminate flooring to size. This will help keep the rest of the floor square. If your beginning wall isn’t parallel to your ending wall, don’t worry; you can make a few cuts to compensate. When you’re finished, the irregularity should not show.

2. When you’re ready to install the floor, apply glue to the edges of each plank. Glue all the way along the long and short edges. Slide each plank into position and use a tapping block to make the joints as tight as possible. Don’t strike the tongue of the plank with the hammer; you might damage it. Install the first three rows and allow them to dry for an hour before you install the remaining planks.

3. When you get to the end of a run and need to make a cut, you may be able to use a scrap piece of flooring. If you have to cut an irregular angle, measure the short and long sides and the point at which the angle begins. Transfer the measurements to the back of the plank and use a saber saw to make the cuts.

4. Stagger the joints within each run so that they are at least 8″ away from the joints of the preceding run.

5. As you get to the ends of the runs, use a pry bar to tighten the joints. You can also use a strap clamp to hold the planks in place as the glue dries.

Finishing touches

1. Install quarter-round shoe molding to cover the expansion gap around the edge of the flooring. The quarter-round will add a finished look to the floor and help hide irregularities.

2. Measure each wall and cut each piece to length. Use a miter saw to make 45-degree cuts for inside and outside corners.

3. Nail the quarter-round into place, making sure you don’t nail through the laminate flooring. You may want to use a pneumatic nailer to speed up the process.

4. Use a reducer strip to make a visual transition between the laminate floor and another type of floor covering such as carpet. Cut the metal mounting strip to the appropriate length and secure it to the floor with screws. Then, cut the reducer strip to length and snap it into the mounting strip.

Leave a Reply

Your email address will not be published. Required fields are marked *